Guitar Buying Guides

7 Best Pedals for Metal 2026: Boost, Gate, Distortion and EQ

By · 9 min read

Best pedals for metal guitar: two high-gain effects pedals wired on a pedalboard

The best pedals for metal do four jobs: tighten the amp, add gain, kill noise and shape the mids. For most players that means an Ibanez TS9 Tube Screamer or Horizon Devices Precision Drive in front of a high-gain amp, an ISP Decimator II noise gate, and an MXR M108S Ten Band EQ. If your amp is clean, the Revv G3, Boss MT-2 Metal Zone and Boss HM-2W supply the distortion itself.

Quick answer: for a high-gain amp, add a boost (Ibanez TS9, $99.99, or Horizon Devices Precision Drive, $220) with gain low and level up, plus a noise gate like the ISP Decimator II. For a clean amp or modeler, use a distortion such as the Revv G3 ($195) for modern tones, the Boss MT-2 ($109.99) on a budget, or the Boss HM-2W ($164.99) for the Swedish death metal sound. An MXR 10-band EQ ($159.99) fixes mud and fizz.

Disclosure: some links in this guide are affiliate links. As an Amazon Associate, Sandy Music Lab earns from qualifying purchases at no extra cost to you, and commissions never decide which products make a list. See our editorial policy.

Which pedals do you need for metal?

You need two pedals for metal at minimum: a gain source (a boosted amp or a distortion pedal) and a noise gate. A boost such as a Tube Screamer tightens the low end of a high-gain amp, and a gate stops hiss and hum between riffs. An EQ pedal is the third most useful addition.

PedalJobKey controlsPower (9 V)Typical price
Ibanez TS9 Tube ScreamerBoost to tighten a high-gain ampDrive, Tone, Level9 V$99.99
Horizon Devices Precision DriveMetal overdrive boost with built-in gateVolume, Bright, Attack, Drive, Gate9 V$220
Revv G3Modern high-gain distortionThree-band EQ, three aggression settings14 mA minimum$195
Boss MT-2 Metal ZoneBudget high-gain distortionThree-band EQ with semi-parametric mids30 mA$109.99
Boss HM-2W Heavy MetalSwedish death metal “chainsaw” toneLow and high EQ, Standard and Custom modes30 mA$164.99
ISP Decimator IINoise gateThreshold9 Vabout $143 to $180
MXR M108S Ten Band EQMid shaping, mud and fizz control10 bands, volume and gain sliders9 V or 18 V$159.99

Specs come from Boss, Revv, Horizon Devices, MXR and ISP, and prices from makers and large US retailers. HM-2W “Standard and Custom modes” refers to Boss’s Waza Craft switch.

What are the best pedals for metal in 2026?

The seven best pedals for metal below are grouped by job, because metal tone is built from a chain rather than one magic box. Sandy Music Lab has not run these through a controlled side-by-side test, so the notes rely on maker specs and how each type of pedal is commonly used.

1. Ibanez TS9 Tube Screamer: best boost for a high-gain amp

The TS9 is the classic way to tighten a high-gain amp: set Drive near zero, Level high and Tone to taste. Its mid-focused EQ trims flabby lows before they hit the amp, which keeps palm mutes punchy. US dealers lists it at $99.99.

Best for: Players with a high-gain tube amp or modeler that sounds loose or muddy.

Check the Ibanez TS9 on Amazon

2. Horizon Devices Precision Drive: best metal-specific boost

Horizon Devices calls the Precision Drive a modern overdrive, with Volume, Bright, Attack, Drive and a built-in adjustable noise gate. The Attack control shapes how hard palm mutes hit, which a standard Tube Screamer cannot do. Horizon Devices lists it at $220. See Horizon Devices’ pedal page.

Best for: Modern djent and progressive metal players who want boost and gate in one box.

Check the Precision Drive on Amazon

3. Revv G3: best modern distortion pedal

Revv says the G3 is distilled from the purple channel of its Generator 120 amp, with a three-band EQ and three aggression settings. It is true bypass and needs a 9 V center-negative supply of at least 14 mA. Revv listed the G3 V2 at $195. See Revv’s G3 page.

Best for: Clean amps, practice amps and direct recording where you need the distortion from the pedal.

Check the Revv G3 on Amazon

4. Boss MT-2 Metal Zone: best budget distortion

The Metal Zone uses a dual-stage gain circuit and a three-band active EQ with a semi-parametric mid control that sweeps from 200 Hz to 5 kHz, with up to 15 dB of boost or cut per band. It draws 30 mA. Sweetwater lists it at $109.99. See Boss’s MT-2 page.

Best for: Tight budgets and players willing to spend time on the EQ.

Check the Boss MT-2 on Amazon

5. Boss HM-2W Heavy Metal: best for Swedish death metal tone

Boss made the original HM-2 from 1983 to 1991, and says its “chainsaw” sound with all knobs maxed became the voice of Swedish death metal. The Waza Craft HM-2W reissue adds a Custom mode next to the original Standard voice and draws 30 mA. Sweetwater lists it at $164.99. See Boss’s HM-2W page.

Best for: Old-school death metal, crust and anyone chasing that buzzsaw midrange.

Check the Boss HM-2W on Amazon

6. ISP Decimator II: best noise gate for metal

The Decimator II uses ISP’s Time Vector Processing, which tracks short staccato notes and long sustained notes without the choppy release of simpler gates. One Threshold knob sets it. US dealers listed it from about $143 to $180. More gates are compared in the best noise gate pedals guide.

Best for: High-gain rigs with hum or hiss between chugs.

Check the ISP Decimator II on Amazon

7. MXR M108S Ten Band EQ: best EQ pedal for metal

The M108S gives ten bands of graphic EQ plus volume and gain sliders. Metal players use it to cut mud around 250 Hz, add bite in the upper mids or tame fizz above 6 kHz, either in front of the amp or in the effects loop. Dunlop lists it at $159.99. See MXR’s Ten Band EQ page, and the best EQ pedals guide for alternatives.

Best for: Fixing a tone that is close but muddy, scooped or harsh.

Check the MXR M108S on Amazon

Why do metal players use a Tube Screamer?

Metal players use a Tube Screamer as a boost, not a distortion: with the drive almost off and the level high, it cuts low end and pushes the mids into an already distorted amp. That tightens palm mutes and adds clarity to fast riffs. It works because high-gain amps get loose and flubby when too much bass hits the preamp.

TS9 setting for metalTypical startWhy
Drive0 to 9 o’clockYou want the amp’s distortion, not the pedal’s
Tone12 o’clockAdjust for bite
Level2 to 5 o’clockPushes the amp’s front end
Amp gainTurn down slightlyThe boost adds gain, so back the amp off

The same idea works with any clean boost or overdrive with a tight low end, including the Precision Drive. If your amp is clean, a boost will not create metal distortion on its own, so start with a distortion pedal instead.

What order should metal pedals go in?

Metal pedals usually go in this order: tuner, wah, boost or overdrive, distortion (if your amp is clean), noise gate, then EQ, and finally modulation, delay and reverb, often in the amp’s effects loop. Placing the gate after the gain catches the noise the gain creates.

  1. Tuner first, for a clean signal to read.
  2. Wah and filters before the gain.
  3. Boost (TS9, Precision Drive) into the amp or distortion.
  4. Distortion (G3, MT-2, HM-2W) if the amp itself is clean.
  5. Noise gate after the gain. Some gates, like the Decimator G-String, can also sit in the loop.
  6. EQ after the gain or in the effects loop to shape the final tone.
  7. Delay and reverb last, ideally in the effects loop.

See the full guitar pedal order guide, or drop your pedals into the free pedal order builder, which flags common mistakes such as a gate placed before the distortion.

Do you need a distortion pedal for metal if your amp has gain?

You do not need a distortion pedal for metal if your amp already has a high-gain channel; a boost and a noise gate will do more for you. A distortion pedal is for clean amps, low-gain practice amps and modelers without good high-gain voices. Stacking a distortion into a high-gain channel usually adds noise and mud.

Your ampBest first pedalSecond pedal
High-gain tube ampBoost (TS9 or Precision Drive)Noise gate
Clean or low-gain ampDistortion (Revv G3 or MT-2)Noise gate
Modeler or amp simUsually none; use built-in boost and gateEQ if needed
Small practice ampDistortion pedalEQ

For amps built for heavy music, see the best guitar amps for metal, and for heavier strings that hold up in drop tunings, the best guitar strings for metal.

How do you power a metal pedalboard?

Power a metal pedalboard with an isolated supply, because high-gain rigs magnify any hum from daisy chains and cheap adapters. The Boss MT-2 and HM-2W draw 30 mA each and the Revv G3 at least 14 mA, so a small board of seven pedals typically needs well under 500 mA in total. Some EQ pedals run at 18 V for more headroom.

Add each pedal to the free pedal power calculator to check current and outputs. If you still hear hum after isolating power, the guitar hum finder walks through the usual causes. More on building the board itself is in how to build a pedalboard.

How we chose the best pedals for metal

We started with the pedals metal players recommend most often on Reddit, forums and YouTube rig rundowns, grouped them by job, and kept one or two current pedals per job with published specs. Every control list and current draw comes from the maker’s page where available, and prices from makers or large US retailers. We have not run a side-by-side test. Sandy Music Lab is written by David Sandy, and the editorial policy explains how guides are researched. For distortion pedals beyond metal, see the best distortion pedals and the main best guitar pedals guide. Think we missed a pedal? Tell us.

Metal pedal FAQs

What is the best pedal for metal?

For a high-gain amp, a boost like the Ibanez TS9 is the best single pedal for metal. For a clean amp, a distortion pedal such as the Revv G3 or Boss MT-2 is the starting point.

Is the Boss Metal Zone good for metal?

Yes, if you take time with its EQ. The MT-2 has a dual-stage gain circuit and a semi-parametric mid control, and it costs $109.99. Many players cut the bass and keep the mids higher than the scooped settings it is known for.

Do I need a noise gate for metal?

Almost always. High gain amplifies hum and hiss between notes, and a gate such as the ISP Decimator II silences it without cutting off held notes.

Where does the noise gate go in a metal rig?

After the gain stage, so it removes the noise the distortion creates. Some gates offer a loop so they can sense the guitar signal before the amp.

Can a Tube Screamer be used for metal?

Yes, as a boost. Set drive low and level high in front of a high-gain amp to tighten the low end.

What does the HM-2 sound like?

A thick, buzzing “chainsaw” distortion with heavy mids when its EQ knobs are maxed. Boss says that sound defined Swedish death metal.

What pedals do I need for djent?

A tight boost (the Precision Drive is built for it), a noise gate and often an EQ pedal, in front of a high-gain amp or modeler.