Electric guitar fret buzz is the rattle of a string against a fret that should not be touching it. Fender’s setup guides point to technique, low action, neck relief, a worn nut and uneven frets as the usual causes. This guide helps you tell those problems apart and explains which checks are safe at home.
Quick answer: First check your fretting hand: buzz all over the neck can mean the fingertip is too light or too far behind the fret. Then look at the guitar. Low action, too little neck relief, a worn nut or high or grooved frets can all cause buzz. You can measure relief with a capo and feeler gauges using Fender’s method; truss-rod changes, nut work and fret dressing belong with a technician if you are not trained.
Related: how to get low action without fret buzz, why acoustic guitar strings buzz and why guitar amps buzz.
Disclosure: some links in this guide are affiliate links. As an Amazon Associate, Sandy Music Lab earns from qualifying purchases at no extra cost to you, and commissions never decide which products make a list. See our editorial policy.
What is electric guitar fret buzz, and when is it normal?
Fret buzz is a rattle you feel and hear when a string hits a fret during a note that should ring clearly. A tiny buzz that you barely hear through the amp can be normal on a very low setup. Buzz that chokes a note, or follows one fret, is a setup or wear problem.
This page is about strings buzzing against frets on an electric guitar, unplugged or plugged in. It is not about 60-cycle hum, a scratchy pot, or an amp that buzzes with the guitar volume at zero. For those, see our guitar hum diagnosis guide and scratchy pot guide.
How can you tell which kind of fret buzz you have?
Fender’s article on how to deal with fret buzz starts with technique: if strings buzz all up and down the neck, you may not be pressing hard enough, or your finger may sit too far behind the intended fret. Move the fingertip close to the fret wire and press firmly, then test again before you change the guitar.
If the buzz remains, map it. Open-string buzz often points to the nut or to too little neck relief. Buzz in the middle of the neck often points to relief or to overall action. Buzz only at the high frets often points to saddle height or to a neck angle issue. Buzz at one fret, on every string that crosses it, often means that fret is high or worn. Old, grimy strings can also rattle and are worth changing first.
| Where it buzzes | Likely cause | Usual next step |
|---|---|---|
| All over the neck, any string | Technique, or action and relief both low | Check fretting hand, then measure relief and action |
| Open strings only | Worn or poorly cut nut, or back-bow | Do not file the nut at home; see a technician |
| Around the middle frets | Not enough neck relief | Measure relief; a technician can adjust the truss rod |
| High frets, near the body | Saddles too low, or neck angle | Raise the saddles a little, or get a setup |
| One fret, several strings | High, worn or unlevel fret | A technician can dress or level the frets |
| Only after a string change | Different gauge, or a string not seated | Check the wrap at the tuner and the saddle; give the neck time to settle |
How do you check neck relief and action on an electric guitar?
Fender’s guide on how to measure neck relief uses a capo and feeler gauges. Capo the first fret, press the low E string at the last fret or the neck joint, and measure the gap at the eighth fret. Repeat the check on the high E string.
For Fender Stratocaster and Telecaster guitars, that guide lists about 0.012 inches (0.3 mm) of relief for a 7.25-inch radius, 0.010 inches (0.25 mm) for 9.5 to 12 inches, and 0.008 inches (0.2 mm) for 15 to 17 inches. Those figures are Fender factory targets, not a rule for every brand or player. Too little relief can cause buzz; too much raises the action and can make the guitar harder to play.
Fender recommends having a qualified technician adjust the truss rod if you measure no relief, or much more than those amounts. You can raise saddle height in small amounts yourself if the buzz is only in the upper frets and the saddles have room to move. a guitar feeler gauge set on Amazon and a guitar capo on Amazon are the two tools that guide names for the relief check. For a lower action that still rings clean, see how to get low action without fret buzz.
Which fret-buzz fixes should a technician handle?
Leave nut work, fret leveling and most truss-rod adjustments to a technician unless you have been trained. Filing a nut slot too deep is hard to undo, and a high fret needs proper tools. A sudden buzz after a drop or a weather change can also need a shop visit.
A full setup looks at relief, nut height, saddle height, intonation and pickup height together. Changing only one of those can move the buzz instead of removing it. If the guitar buzzes in some rooms or seasons and not others, humidity and neck relief are worth checking before you assume the frets are worn.
How we researched this guide
We used Fender’s fret-buzz and neck-relief articles as the official reference for causes and for Fender-brand relief targets, and we kept those numbers labeled as Fender specs rather than a universal measurement. Acoustic string buzz and “how low can action go” already have their own posts, so this one stays on electric fret buzz diagnosis.
If you spot an error, tell us. Sandy Music Lab is written by David Sandy, and our editorial policy explains how we work. Related reading includes low action without fret buzz, acoustic guitar string buzz and guitar maintenance.
Electric guitar fret buzz FAQs
Why does my electric guitar buzz when I fret a note?
The string is hitting a fret it should clear. That can be technique, low action, too little neck relief, a worn nut, a high or grooved fret, or a mix of those. Map where the buzz happens before you change anything.
Is a little fret buzz normal on an electric guitar?
A very small amount that you feel more than you hear through the amp can be normal on a low setup. Buzz that chokes a note, or that you can hear clearly unplugged, is worth fixing.
Can bad technique cause fret buzz?
Yes. Fender notes that buzz all up and down the neck can mean you are not pressing hard enough, or that your finger is too far behind the fret. Place the fingertip close to the fret wire and test again.
How do I measure neck relief?
Fender’s method is to capo fret 1, press the string at the last fret or the neck joint, and measure the gap at the eighth fret with feeler gauges. Compare what you find with the specs for your guitar, not with a single number for every instrument.
Should I adjust the truss rod myself?
Fender suggests having a qualified technician adjust the truss rod if relief is missing or far from spec. A small turn the wrong way can make buzz worse or bow the neck. If you have not been shown how, get a setup.
Why do only my open strings buzz?
Open-string buzz often points to nut slots that are too low, or to a neck with too little relief. Do not file the nut at home. A technician can recut or replace it and then reset relief.
Is this the same as a buzzing amp or humming pickups?
No. Fret buzz is mechanical, from a string hitting a fret. Amp buzz and pickup hum are electrical. If the guitar is quiet unplugged but the amp still buzzes, see our amp-buzz and hum guides.


